How To Get Jon Boat Off Trailer on Land? (A Step-By-Step Guide)


Getting a Jon Boat off the trailer and into the water can be a daunting task, but with the right preparation and know-how, it does not have to be a stressful experience.

In this article, we will provide a step-by-step guide on how to get your Jon Boat off the trailer on land from preparing the boat and trailer, unhitching the trailer from the vehicle, rolling the trailer backwards, and raising the boat off the trailer.

We will also discuss using a block of wood or jack to lift the boat, moving the boat to the water, and securing the boat in the water.

So if you’re ready to get your Jon Boat off the trailer and into the water, then let’s get started!

Short Answer

To get a jon boat off a trailer on land, you will need to back the trailer up to a ramp or dock, then use a winch to pull the boat off the trailer.

Once the boat is off the trailer, you can use a jacking device to lift the trailer out of the water.

Once the trailer is out of the water, you can then unhook it from the hitch and store it somewhere on the land.

Preparing the Jon Boat and Trailer

When it comes to getting your jon boat off the trailer on land, preparation is key.

The first step is to make sure that the boat is adequately secured to the trailer with the winch and straps.

This will ensure that the boat is not only secure while it is being transported, but also that it will be easy to detach from the trailer once it is on land.

After the boat is secured to the trailer, it is important to make sure that the trailer is placed on level ground.

This will help ensure that the boat is able to move freely off the trailer without any difficulty.

Once these steps are taken, you can then unhitch the trailer from your vehicle and let it roll backwards.

Unhitching the Trailer from the Vehicle

Unhitching the trailer from the vehicle is an important step to getting your jon boat off the trailer on land.

Before you begin, make sure that the trailer is securely attached to your vehicle and that the trailer is on level ground.

Once you have this in place, you can move on to unhitching the trailer from the vehicle.

The first step is to release the trailers coupler from the hitch ball on your vehicle.

If your trailer has a safety pin, make sure that it is removed.

Then, using a wrench, loosen the couplers latch so that it can be released from the ball.

Once the coupler is loose, you can release it from the hitch ball.

Next, you will need to disconnect the trailers safety chains.

Before you do this, make sure that the chains are not twisted or tangled.

If they are, you will need to untangle them before you can proceed.

Once the chains are untangled, you can then disconnect them from the vehicles frame.

Finally, if your vehicle has a trailer brake, you will need to disconnect it as well.

This can usually be done by removing the pin that connects the brake to the trailer.

Once the brake is disconnected, you can then proceed to unhitch the trailer from the vehicle.

Once the trailer is unhitched, you can then let it roll backwards until the boat is far enough away from the trailer.

At this point, you can then use a block of wood or a jack to raise the boat off the trailer and move it to the water.

With the proper steps taken, you can now get your jon boat off the trailer on land.

Rolling the Trailer Backwards

Rolling the trailer backwards is an important step in getting your jon boat off the trailer.

The first thing you should do is make sure that the trailer is on level ground and that the boat is properly secured with the winch and straps.

This will ensure that the boat doesn’t shift while you are rolling the trailer backwards and make the process more difficult.

Once the trailer is situated, you can then unhitch it from your vehicle and let it roll backwards.

It is important to note that the trailer should be rolling at a slow and steady pace.

If you roll it too quickly, the boat can shift and cause damage.

Also, if you are rolling the trailer on an incline, you should be extra careful as the trailer could roll too quickly and become difficult to control.

Once the boat is far enough away from the trailer, you can then use a block of wood or a jack to raise the boat off the trailer.

Raising the Boat off the Trailer

Raising the boat off the trailer is the final step in getting your jon boat off the trailer on land.

Though it may seem intimidating at first, it is actually quite simple and straightforward.

To begin, you will need to make sure that the trailer is on level ground.

This is important, as an uneven trailer can cause the boat to become unbalanced during the lifting process.

Once the trailer is level, you can then use a block of wood or a jack to raise the boat off the trailer.

When using a block of wood, you will need to place the block of wood between the trailer frame and the hull of the boat.

You will then need to lift the block of wood until the boat is off the trailer.

Make sure that the block of wood is properly secured before you begin lifting the boat, as the boat can easily become unbalanced.

When using a jack, you will need to make sure that the jack is the appropriate size and weight for the boat.

The jack should also be positioned on a stable surface.

Once the jack is in place, you can then begin to slowly lift the boat off the trailer.

Be sure to lift evenly on both sides of the boat, as any imbalance can cause the boat to become unbalanced.

Once the boat is off the trailer, you can then move it to the water.

Be sure to secure the boat to the trailer with ropes or straps to prevent it from becoming unbalanced and to ensure that it remains safe and secure during the journey.

With the right preparation and tools, getting your jon boat off the trailer on land can be a relatively simple and straightforward process.

Just remember to take your time and make sure that the trailer is level, the block of wood or jack is properly secured, and that the boat is properly secured to the trailer before you attempt to lift it off.

With these steps, you can safely and successfully get your jon boat off the trailer on land.

Using a Block of Wood or Jack to Lift the Boat

Using a block of wood or a jack to lift the boat off the trailer is a simple but effective way to get your jon boat unstuck from the trailer without having to move the trailer itself.

First, make sure the trailer is sitting on level ground before you begin.

This will ensure that the boat remains stable and secure while it is being lifted.

Next, use the winch and straps to securely tie the jon boat to the trailer.

This will ensure that the boat does not move around too much while it is being lifted.

Once the boat is secured, you can then use a block of wood or a jack to begin lifting the boat off the trailer.

When using a block of wood, place the block under the boat’s hull and then use a lever or your hands to slowly lift the boat up off the trailer.

This should be done slowly and carefully to ensure that the boat does not shift or move around too much.

You can also use a jack to lift the boat off the trailer.

To do this, you will need to place the jack under the boat and then slowly lift it up until the boat is off the trailer.

When the boat is off the trailer, you can then move it to the water.

Make sure to double check that the boat is still securely tied to the trailer before you begin moving it.

This will ensure that the boat stays in place while it is being moved.

With these steps, you should now have a better understanding of how to get your jon boat off the trailer on land.

Moving the Boat to the Water

Once the boat is off the trailer, you can then move it to the water.

To do this safely, you’ll want to make sure you have the right equipment and the right plan.

First, you’ll need a dolly or a wheelbarrow to move the boat.

A dolly can be a great option because it will help you move the boat across the beach or other terrain without too much effort.

You can also use a wheelbarrow if you want to move the boat over a longer distance.

Once you have the dolly or wheelbarrow, you’ll want to make sure that the boat is securely fixed to the dolly.

You can do this by tying the boat to the dolly or by using straps.

You’ll also want to make sure that the dolly is on level ground and that the wheels are in good condition.

After the boat is securely attached to the dolly, you can then start pushing it to the water.

If the boat is heavy, you may need to enlist the help of a friend to help you move it.

Once you get close to the water, you can then use a rope or a tow line to drag the boat to the water’s edge.

Once the boat is in the water, you can then secure it to a dock or mooring, or simply leave it beached until you’re ready to take it out.

Securing the Boat in the Water

Securing your Jon Boat in the water is an essential step when getting it off the trailer on land.

This is an important step that should not be overlooked, as it will ensure that the boat is properly secured and ready for transport.

The first step is to make sure the trailer is on level ground.

This will help to ensure that the boat is properly secured in the water and will also prevent the trailer from tipping over.

Once the trailer is on level ground, you can then attach the winch and straps to the boat.

This will help to keep the boat firmly in place and will also prevent it from sliding off the trailer.

Once the winch and straps are in place, you can then begin to un-hitch the trailer from your vehicle.

This will allow the trailer to roll backwards until it is far enough away from the boat.

At this point, you can then use a block of wood or a jack to raise the boat off the trailer.

This should be done slowly and carefully so that the boat is not damaged in the process.

Once the boat is off the trailer, you can then move it to the water.

Make sure to use the winch and straps to firmly secure the boat in the water.

This will help to ensure that the boat does not drift away or get caught in the current.

It is also important to ensure that the boat is pointed in the right direction and is stable in the water.

By following these steps, you will be able to get your Jon Boat off the trailer on land and into the water safely and securely.

Final Thoughts

Now that you understand the steps for getting your jon boat off the trailer on land, you’re ready to try it out! Start by properly securing the boat on the trailer, and making sure the trailer is on level ground.

Then unhitch the trailer from your vehicle and roll it backwards.

With a block of wood or a jack, you can then lift the boat off the trailer and move it to the water.

Finally, secure the boat in the water and you’re all set to enjoy a day out on the lake.

So what are you waiting for? Get out there and get your jon boat off the trailer!

James Frami

At the age of 15, he and four other friends from his neighborhood constructed their first boat. He has been sailing for almost 30 years and has a wealth of knowledge that he wants to share with others.

Recent Posts